A1DrugTest.com

This test card tests for combination of Cocaine, Amphetamine, Methamphemine, Marijuana(THC), Methadone, Opiates, Phencyclidine, Barbiturate, Benzodiazepine, Propoxyphene, Oxycodone, and Tricyclics.

Our Cocaine / Amphetamine / Methamphetamine / Marijuana (THC) / Methadone / Opiates / Phencyclidine / Barbiturate / Benzodiazepine / Tricyclics / Propoxyphene and Oxycodone drugs tests are:


* FDA Approved Tests
* A simple to administer dip-and-read test designed to detect a specific drug(s) in urine
* Results are ready in just a few minutes
* 95% to 98% accurate
* Set to the SAMSHA Cut-off levels

Click here for Test Directions.
Click Here for Package Insert

Configurations of the One Step -Drug Screen Test Card consists of combination of Cocaine, Amphetamine, Methamphetamine, Marijuana (THC), Opiate, Phencyclidine, barbiturate, Benzodiazepine drug analytes. This assay provides only a preliminary analytical test result. A more specific alternate chemical method must be used in order to obtain a confirmed analytical result. Gas chromatography/mass spectrometry (GC/MS) is the preferred confirmatory method. Clinical consideration and professional judgment should be applied to the drug of abuse test result, particularly when preliminary positive results are indicated.

• 
  
• Allow test card & urine specimen to reach room temperature ( 15-30° C ) prior to testing.
• 1. When ready to perform the test, remove the test card from the pouch. Discard the small moisture absorbent packet.
• 2. With arrows pointing towards the urine specimen, immerse the test strip vertically in the urine specimen for at least 10-15 seconds. Do not pass the maximum (MAX) line on the test strip when immersing the strip.
• 3. Place the Test Card on a non-absorbent flat surface. Start the timer & wait for the red lines to appear. The results should be read at 5 minutes. Do not interpret results after 10 minutes.
• 
  
  
   
• POSITIVE RESULT: One red line appears in the Control (C) region. No line appears in the Test (T) region.
• NEGATIVE RESULT: Two red lines appear. One red line should be in the Control (C) region & another red or pink line should be in the Test (T) region.
• INVALID RESULT: Control (C) line fails to appear. Insufficient specimen volume or incorrect procedural techniques are the most likely reasons for the Control line failure.
• LIMITATIONS:
• 1. The One Step Test Strip provides only a qualitative, preliminary analytical result. A secondary analytical method must be used to obtain a confirmed result. Gas Chromatography/Mass Spectrometry (GC/MS) are the preferred confirmatory methods.
• 2. It is possible that technical or procedural errors, as well as other interfering substances in the urine specimen may cause erroneous results.
• 3. Adulterants, such as bleach and/or alum, in urine specimens may produce erroneous results regardless of the analytical method used. If adulteration is suspected, the test should be repeated with another urine specimen.
• 4. Certain medications/pharmaceuticals/compounds may produce a Positive Result.
• 5. A Positive Result indicates presence of the drug or its metabolites but does not indicate level of intoxication, route of administration or concentration in urine.
• 6. A Negative Result may not necessarily indicate drug-free urine. Negative Results may be obtained when drug is present but below the cutoff level of the test.
• 7. The test does not distinguish between drugs of abuse & certain medications
• a1 drug test.com products have been found to be highly accurate and are guaranteed against defects in labeling & packaging until the stated expiration date.
• Regardless, a1 drug test.com will not be held accountable/liable for the outcome of ANY result arising from the use of Drug Test Strips products.
• a1 drug test.com sole obligation in the event of ANY damage/result/defect is to replace it with a comparable new test strip product. Except for such replacement, the sale, transfer, or handling of these drug test products are without warranty, condition or liability even though the damage/result/defect is due to negligence or other fault.